Home > Antenna Feeder Devices > Amateur Antennas >

Antennas HF RM Series, 10-80m (3.5-30MHz), RM10-RM80
Antennas HF RM Series, 10-80m (3.5-30MHz), RM10-RM80


 
Alternative Views:


Our Price: $19.95

Product Code: RM


Hustler Model:


Optional Accessories:


Qty:  
Description
 
Hustler resonators are designed for use with 54-inch mast, models MO-1, MO-2, MO-3 and 22” MO-4 mast. Under the clutch nut is a barrel shaped clutch sleeve. The nut and sleeve work together to hold the rod. If you find it necessary to remove the clutch nut use caution, as the clutch sleeve will fall out and is easily lost. To assemble your resonator loosens the clutch nut and slide the rod 4 inches into the receptacle tube. Tighten the clutch nut to secure whip and screw the resonator onto the mast. Using a good quality V.S.W.R meter check the resonate frequency. If it is too low, loosen the clutch nut and push the tip rod into the tube in ¼ inch increments until the desired frequency is reached. To lower the resonance frequency extend the rod in ¼ inch increments. If it becomes necessary to trim the rod use a file to score the rod at the cut point. Always trim the rod at least 4” (10.16 cm) longer than the given lengths to insure it is not cut too short. Also note when using a resonator mounted on a MO-4 22” (55.88 cm) mast the required exposed tip rod length will be approximately 1” (2.54 cm) longer. Wear safety glasses or other adequate eye protection, place the rod on a table or similar sharp edge and use a hammer to snap off the excess rod. Use a file to deburr the rough end. There are several accessories available for you Hustler HF mobile system. VP-1 Multi-band adapter: accepts 3 resonators for multi-band use. RSS-2 Spring: mounts between resonator and mast. QD-2 Quick Disconnect: recommend for easy removal of you mast. MO-1, MO-2, MO-3 - 54-inch mast MO-4 - 22-inch mast

Standard Resonator

Tip Rod Length (inch)

Bandwidth

(2:1 SWR or Better)

Super Resonator

Tip Rod Length (inch)

Bandwidth

(2:1 SWR or Better)

RM-10

12 5/8

150-250 KHz

RM-10S

12 13/16

250-400 KHz

RM-11

12 5/8

150-250 KHz

RM-11S

18 5/8

250-400 KHz

RM-12

18 7/16

100-150 KHz

RM-15S

16 5/16

150-200 KHz

RM-15

12 5/8

100-150 KHz

RM-20S

18 5/8

100-150 KHz

RM-17

23 1/4

80-100 KHz

RM-40S

32 5/16

50-80 KHz

RM-20

18 7/16

80-100 KHz

RM-75S

32 5/16

50-60 KHz

RM-30

18 7/16

50-60 KHz

RM-80S

40 5/16

50-60 KHz

RM-35

40 1/8

50-60 KHz

RM-40

32 1/8

40-50 KHz

RM-50

40 1/8

40-50 KHz

RM-60

40 1/8

40-50 KHz

RM-75

32 1/8

25-30 KHz

RM-80

40 1/8

25-30 KHz

Features
  • Standard ResonatorTip Rod LengthBandwidth (2:1 SWR or Better)
    RM-1012 5/8150-250 KHz
    RM-1112 5/8150-250 KHz
    RM-1218 7/16100-150 KHz
    RM-1512 5/8100-150 KHz
    RM-1723 1/480-100 KHz
    RM-2018 7/1680-100 KHz
    RM-3018 7/1650-60 KHz
    RM-40
    32 1/840-50 KHz
    RM-6040 1/840-50 KHz
    RM-7532 1/825-30 KHz
    RM-8040 1/825-30 KHz
    Super Resonator Tip Rod Length Bandwidth (2:1 SWR or Better)
    RM-10S12 13/16250-400 KHz
    RM-11S18 5/8250-400 KHz
    RM-15S16 5/16150-200 KHz
    RM-20S18 5/8100-150 KHz
    RM-40S32 5/1650-80 KHz
    RM-75S32 5/1650-60 KHz
    RM-80S40 5/1650-60 KHz

Share your knowledge of this product. Be the first to write a review »