Viper-SC Base Station Standard, IP Router & Wireless Modem.

Viper-SC Standard Base Station
IP Router & Wireless Modem VHF, UHF, 900 MAS 

The Viper Base Station uses a single radio to transmit and receive data from remote radios and has a main controller PC board which is accessible via HTML web pages. Access the Controller’s web pages to configure the user programmable settings and to view the status of the Base Station. The Viper Base Station is housed in a rugged, 19" rack mountable, aluminum case. Built for industrial applications in a variety of environments, The Viper Base Station operates over an extended temperature range and provides worry-free operation in the roughest environments. 

Viper SC Base User Manual.pdf


Base Station Specifications
 

These specifications are typical and subject to change without notice. General
Power Source					11-30 VDC, Negative GND
RF Impedance					50 Ω
Operating Temperature					-30° to + 60° C
Storage Temperature					-40° to + 85° C
Operating Humidity					5% to 95% non-condensing RH
Rx Current Drain at 25°C with one Viper powered.		DC Input 11V			DC Input 20V			DC Input 30V
All Relays On All Relays Off		1.7 A (max) 1.5 A (typ) 1.3 A (typ)			1.2 A (max) 945 mA (typ) 925 mA (typ)			760 mA (max) 646 mA (typ) 622 mA (typ)
Tx Current Drain at 25°C with one Viper powered.	Power Out			DC Input 11V		DC Input 20V			DC Input 30V
Tx Pwr: Max All Relays On All Relays Off		6.7 A (max) 4.5 A (typ) 4.3 A (typ)			4.7 A (max) 3.1 A (typ) 2.9 A (typ))			2.9 A (max) 1.9 A (typ) 1.7 A (typ)
Tx Pwr: 1W All Relays On All Relays Off		2.6 A (max) 2.1 A (typ) 1.9 A (typ)			1.7 A (max) 1.4 A (typ) 1.2 A (typ)			1.1 A (max) 880 mA (typ) 860 mA (typ)
Cold start					60 seconds
Nominal Dimensions					Chassis: 16" W x 4.75" H x 11.375" D (41 x 12 x 29 cm) Front Panel: 19" x 5.22" x 0.25" (48 x 13 x 0.6 cm)
Shipping Weight					Standard: 11.5 lbs. (5.2 kg) Repeater/Redundant: 15 lbs. (6.8 kg)
Mounting Options					19" Rack Mount
RF Specifications					See radio specifications and user manual
FCC / IC Certifications					See radio specifications and user manual
Display
12 Status LEDs (Standard) 17 Status LEDs (Redundant)					Controller LEDs: Power, Status, Fan Error Data LEDs: COM Data, Setup Data, Link/Act 1, Link/Act 2 Radio LEDs: Tx, Power, Error, Link/Act Other: Alarm Disabled, Manual Override (Redundant Models only)
Connectors
Antenna Connector					N Female (Tx/Rx)
Serial Setup Port					DE-9F
Serial Com Port					DE-9F
Ethernet RJ-45					Two 10/100 BaseT auto-MDIX (The 2 Ethernet connections are connected internally to each other and to the radio(s) with an embedded Ethernet Switch.)
Main Power			Power Header				Power Plug
4 Pin, 5.08mm, Power Header					4 Pin, 5.08mm Power Header Cable: 60 inches Connections: Aux Power A Ground